Wednesday 4 January 2012

Terrain is everything - Dawn of War Plasma Generator part 2.

Thanks to MasterSlowPoke you all know my next terrain effort - the Dawn of War Plasma Generator. Of course this picture may elicit a call of "foul" - another one of those step-by-step guides that just goes from A - D, bypassing B and C but it's pretty straightforward, just fiddly in places. The white stuff is foamcard [obviously] and the black stuff is a laminate of three pieces of thin card.


The black is a textured folder card for use on report covers, I thought the texture might show up and be cool. There's a thin piece of grey cereal box type card sandwiched between the black, end result 1.5mm card. I was aiming for 1mm, if I'd have only used one piece of black that probably would have done it. Alternatively mounting card will do but I found this dead easy to cut, which was my concern over mounting card.


Masking tape was used to cap the foamcard in places, 8mm strips of my laminate in the reinforced areas. Mounting card was also used on the lower parts, with the two holes punched in. Later on I thought this a bit much as visually it takes away the horizontal line and instead continues the slope, which isn't the correct profile, but never mind.


As you can see I've used a CD base to create a standalone modular socket. This can can obviously be used on it's own or I can mount the Plasma Generator in any of the other modular sockets I've made so far, man-made hills for instance, though I doubt it'd work on top of the Vent Tower! Here's a marine so you can see the scale. I think it's actually taller than the DOW model but I think it benefits from the increase in scale.


Of course you are dieing to know about the plasma tubes... Simple, it's a Biro, chopped at the top, filled with any form of coloured gel*, handwash in this case and capped with hot melt glue. Now there is a knack to filling these, which I found out the hard way. I used a syringe to load them up but as soon as you start to fill them air gets trapped and the gel will come out backwards, not fill the tube, if you still have the coloured end cap at the bottom [which I did]. Now you can't really take the end cap out but if you put a tiny hole in it then as the gel fills it up the air can escape through the hole. If you use a needle file to puncture it from the inside it's relatively simple to press the plastic back in place until you can cover it with hot melt glue and seal it. Alternatively if you have the glue on hand you can seal it immediately.


As you can see bubble can be trapped in place but they do settle after a while. One note is that the colour is a lot paler than you will see in your gels normal container, this is obviously because you are looking through only a thin tube, not an inch or two of gel. I'm thinking bath bubble mixture may be slightly more vibrant in colour and definitely offer up more variety, reds and even pearlescent mixtures. I wanted the standard blue but I'd wanted to paint the structure Hawk Turquoise which I don't think will allow the plasma tubes to stand out so I've had to rethink that option.

  
I'm loathe to do another Ferron red structure, I wanted this to be metal so I'm thinking of doing the main structure yellow, and to weather it in as close an approximation of the rail crane at Appley Bridge Station. I'm not entirely convinced it'll work, as my efforts in yellow so far have been less than I'd hoped. Still, this could be my opportunity to get it right. The white bits will either be solid black or black/white chevrons. Overall though it's going to be a tough paintjob as I have to paint it unassembled as I don't want the plasma tubes to get spray or paint marks on them. Oh, the following shot should show up the folder card texture clearly.


So next to finish up is the venting on the sides, paint it with my usual black mixture and then Red Oxide primer as a base to put the Iyanden Dark Sun stippling on.

* I've just realised you don't have to use gel at all to colour the plasma tubes, you could use any coloured liquid or even paint. Water mixed with food colouring or even blackcurrant or orange juice depending on your desire. They'd probably be easier to fill as well, not needing the hole to allow air to escape.

13 comments:

  1. This is a great idea! Lookin' good!

    ReplyDelete
  2. oh man.. if you put a few LED's under those tubes......

    that's awesome terrain.. and this idea might just have been "looted" :)

    don't suppose you've got scannable templates for those struts? :)

    ReplyDelete
  3. Cheers guys, as with all my scratch builds these start life as Illustrator files and in time will be released for you to make at your leisure. due to the interest I may endeavour to finish the templates of sooner, rather than later.

    As I said at the beginning of the project the templates are dependant on the card stock used so there will inevitably be components I can't plan for so this will be very much an STC that requires the constructor to think about their build and fill in any blanks, if you follow.

    ReplyDelete
  4. Cheers guys, as with all my scratch builds these start life as Illustrator files and in time will be released for you to make at your leisure. due to the interest I may endeavour to finish the templates of sooner, rather than later.

    As I said at the beginning of the project the templates are dependant on the card stock used so there will inevitably be components I can't plan for so this will be very much an STC that requires the constructor to think about their build and fill in any blanks, if you follow.

    ReplyDelete
  5. wow that came out great. i may have to try to build one just based off of these pics tommaro...

    ReplyDelete
  6. Well you ain't seen nothing yet, the paint job is working well although I'm not 100% on some of the colour choices. You can go ahead or wait a bit for the STC I will make them a priority to be online, though that doesn't guarantee any deadline...

    ReplyDelete
  7. A very nice idea! I think I'll join the crowd thinking of constructing a homage to this!

    ReplyDelete
  8. I love the idea. But I think that textured card is holding you back. it's thickness and stiffness means that you are getting lots of exposed edges which (imo) are unsightly. (I've been putting together some basic foamboard tutorials if you are interested)

    I think this could be improved if you were to use simple cereal packet card over the foam board base. I'd use a textured spray to add the texture...

    finally, I assume that you've got templates but can't seem to spot teh link to them in your post. Any chance for them?

    ReplyDelete
  9. Thanks for the tips oink. Ordinarily I'd have found a better solution and perhaps filled in the gaps a bit better but compromises have to be made hence the lack of LEDs. The paint job eliminates some, if not all of your concerns [still some gaps :( ]

    The templates aren't ready just yet. Usually I build it, share the WIPs shots, in the process get to iron out the issues and once complete post the STC. It seems the interest in this will require me to supply plans early and trust everyone will be patient that it may not be 100% upto my usual standard. I will get it done soon.

    ReplyDelete
  10. You might want to mention that a Biro is a pen; I've never heard that term living in the US.

    ReplyDelete
  11. Cheers for the International knowledge MasterSlowPoke, I actually didn't know whether to say Biro, or BiC. I think in the UK most people call them Biros as Lazlo Biro was the inventor of the ballpoint process that BiC eventually licensed to use in their pens. Somehow, like calling vacuum cleaners Hoovers [though currently Mr Dyson would wish otherwise] biros seems to have stuck as the name for a crystal ballpoint pen, which is what you will need.

    ReplyDelete
  12. BIC Cristal Stick Ballpoint Pens

    is what i got to use i got them from my local "office max" 12 pens were just over 3$

    very cheep and exectaly what we all need to get these built :)

    ReplyDelete